Western Digital WD10JPVX Есть бэды(можно использовать в качестве Флешки)

Полный отчет о состоянии SMART

smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-4-amd64] (local build)
Copyright (C) 2002-11 by Bruce Allen, smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model: WDC WD10JPVX-00JC3T0
Serial Number: WD-WX41AA3H5589
LU WWN Device Id: 5 0014ee 2b4335921
Firmware Version: 01.01A01
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 9
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sat Dec 27 09:46:50 2014 KRAT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (17460) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 195) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 128
3 Spin_Up_Time 0x0027 184 184 021 Pre-fail Always - 1791
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 35
5 Reallocated_Sector_Ct 0x0033 134 134 140 Pre-fail Always FAILING_NOW 2822
7 Seek_Error_Rate 0x002e 196 196 000 Old_age Always - 2821
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 4602
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 35
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 34
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 277
194 Temperature_Celsius 0x0022 120 105 000 Old_age Always - 27
196 Reallocated_Event_Count 0x0032 097 097 000 Old_age Always - 103
197 Current_Pending_Sector 0x0032 001 001 000 Old_age Always - 65348
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 4
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 199 199 000 Old_age Offline - 320

SMART Error Log Version: 1
ATA Error Count: 71 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 71 occurred at disk power-on lifetime: 4574 hours (190 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 45 00 00 00 a0 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 45 00 00 00 a0 02 12d+21:42:19.688 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 02 12d+21:42:19.672 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 02 12d+21:42:14.123 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 02 12d+21:42:14.108 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 02 12d+21:42:08.570 SET FEATURES [Set transfer mode]

Error 70 occurred at disk power-on lifetime: 4574 hours (190 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 45 00 00 00 a0 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 45 00 00 00 a0 02 12d+21:42:14.123 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 02 12d+21:42:14.108 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 02 12d+21:42:08.570 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 02 12d+21:42:08.533 IDENTIFY DEVICE

Error 69 occurred at disk power-on lifetime: 4574 hours (190 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 45 00 00 00 a0 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------